Proscience Book a seat

Lecture 1 · Capillarity, Angle of Contact & Meniscus · Note · Free

Chapter 9 — Capillarity, Angle of Contact & Meniscus | Notes

Lesson — Angle of Contact, Meniscus & Capillarity

Physics 2027 | Class 12 | Chapter 9 | Based on textbook §§10.49–10.53

1. Angle of contact (θ)
The angle between the tangent to the liquid surface at the point of contact and the solid surface, measured through the liquid, is the angle of contact.

It depends on the nature of the liquid and solid, cleanliness of the surface, surrounding medium and temperature.

Wetting: θ < 90°, concave meniscus (water in clean glass, approximately 8°). Non-wetting: θ > 90°, convex meniscus (mercury in glass, approximately 138°). θ = 90°: plane meniscus (pure water in silver, textbook idealisation).

2. Shape of meniscus: force balance

At the contact line three interfacial tensions act: σSV (solid–vapour), σSL (solid–liquid) and σLV (liquid–vapour). For ideal static equilibrium, resolving along the wall gives:

σSV = σSL + σLV cos θ
cos θ = (σSV − σSL)/σLV

If σSV > σSL, cos θ > 0 and the meniscus is concave. If σSV < σSL, cos θ < 0 and the meniscus is convex. If equal, θ = 90° and the surface is plane.

3. Capillarity
Capillarity: Rise or fall of a liquid in a very narrow tube relative to the surrounding free surface, due to surface tension and wetting behaviour.

Water rises in clean glass; mercury is depressed. Examples: blotting paper absorbing ink, oil rising in a lamp wick, moisture moving through towels, sap movement through fine plant pathways, ink drawn through a split pen nib.

4. Derivation of capillary rise (ascent formula)

Consider a vertical capillary of internal radius r, liquid density ρ, surface tension σ, contact angle θ, and height of rise h.

Radius of curvature of spherical meniscus: r = R cos θ. Pressure jump across the curved interface: Δp = 2σ/R = 2σ cos θ/r. At equilibrium, this balances hydrostatic pressure ρgh.

ρgh = 2σ cos θ/r
h = 2σ cos θ/(rρg)

Equivalent vertical-force approach: upward component of surface-tension force 2πrσ cos θ balances weight πr²hρg, neglecting meniscus volume.

Consequences: h ∝ σ, h ∝ cos θ, h ∝ 1/r, h ∝ 1/ρ and h ∝ 1/g. Narrower tubes give greater rise. For θ > 90°, cos θ is negative and h is negative (depression).

Meniscus correction: If meniscus volume is accounted for, the textbook gives approximately h = 2σ cos θ/(rρg) − r/3 for a narrow wetting capillary, where h is measured to the lowest point of the concave meniscus. The correction is negligible for very small r.

5. Insufficient-height capillary tube

If the tube length h′ is less than the normal rise h, liquid reaches the top and adjusts its meniscus curvature; it does not necessarily overflow. Using h = 2σ/(Rρg) and h′ = 2σ/(R′ρg) (same liquid), hR = h′R′, so R′ = hR/h′. Since h′ < h, R′ > R: the meniscus becomes flatter.

6. Solved numerical 1 — rise in a glass tube

Given: diameter 1.5 mm, σ = 7.4 × 10−2 N/m, ρ = 1000 kg/m³, θ = 0°, g = 9.8 m/s².

r = 0.75 mm = 7.5 × 10−4 m.

h = (2 × 0.074)/(0.00075 × 1000 × 9.8) = 0.02014 m = 2.014 cm.
7. Solved numerical 2 — find surface tension

Given: h = 7.0 cm, r = 0.1 mm, ρ = 0.8 × 10³ kg/m³, θ = 0°, g = 10 m/s².

σ = hrρg/(2 cos θ) = (0.07 × 0.0001 × 800 × 10)/2 = 2.8 × 10−2 N/m.
8. Solved numerical 3 — U-tube with unequal capillaries

Diameters 3.0 mm and 6.0 mm; r₁ = 1.5 × 10−3 m and r₂ = 3.0 × 10−3 m; σ = 0.073 N/m, ρ = 1000 kg/m³, g = 9.8 m/s², θ = 0°.

Δh = (2σ cos θ/ρg)(1/r₁ − 1/r₂)
= (0.146/9800)(1/0.0015 − 1/0.003)
= 0.004966 m ≈ 4.97 mm.
Textbook check: The photographed worked example prints 5.290 mm, but substituting the stated data gives approximately 4.97 mm. The printed calculation appears to contain an arithmetic inconsistency.
Exam tips

Always convert millimetres to metres; use radius (not diameter); show cos θ; write units N m−1 for surface tension; state why h becomes negative for mercury. In derivations, label the meniscus, r, R, θ and h.

Come and see us

Message us on WhatsApp and we will answer the same day.